Products for Adhesives/Primers
Sarnacol® 2170 Adhesive
Sarnacol 2170 is a solvent-based reactivating adhesive used with a Sika Sarnafil adhered system and/or flashing detail. It is also used to adhere flashings in Sarnafil waterproofing systems. It is formulated for adhering Sarnafil PVC membranes to properly prepared substrates such as wood, sheet steel, masonry, concrete and approved coverboards.
Sikaflex 1a is a premium-grade, high-performance, moisture-cured, one-component polyurethane-based, non-sag elastomeric sealant used in certain Sika Sarnafil roofing or waterproofing system flashing details. Typical applications include wall, curb and drain terminations. It is also used as a sealant at pipe penetrations and under certain metal flashings.
Repair & Protection
Sikaflex Primer 449 is used to promote adhesion to pvc, solvent-based enamel, PPG’s fluorocarbon
Duranar-finish, and certain plastics such as ABS and Plexiglass.
Sikaflex Primer 449 is a specially formulated solvent-based primer used to promote the adhesion of Sarnafil G459 Grid Strip flashing membrane to the grid adhesive. Sikaflex Primer 449 must be used on all G459 Grid Strip flashing installations.
Sarnafiller is a pourable two component urethane sealant used as a pitch pocket filler for roofing applications.
Sarnafiller is also used as a grid adhesive to bond the Sarnafil G459 flashing membrane to an acceptable substrate in waterproofing applications.
Sikaflex® 11 FC
Sikaflex-11 FC is a one-component, gun-grade, adhesive and sealing compound of permanent elasticity.
As an elastic adhesive for:
- Cover plates, gaskets and coverings.
- Acoustic ceiling tiles.
- Floor moldings and door sills.
- Light weight construction materials.
- Wood or metal and door frames.
- Roof tiles.
As an elastic joint sealer for:
- Air ducts and high vacuum systems.
- Containers, tanks, and silos.
- Gaskets in openings in walls or floors for ducts, piling, etc.
- Reservoirs or water retaining structures.
- Aluminum fabrication.
- Bolted lap joints.
Characteristics and Advantages
- Excellent adhesion on all cement-based materials, brick, ceramics, glass, metals, wood, epoxy, polyester and acrylic resin.
- Fast cure rate.
- Good weathering and water resistance.
- Can be painted over with water, oil, and rubber-based paints. (Preliminary tests recommended).
- High durability.
PackagingDisposable 10.1 fl. oz., moisture-proof composite cartridges, 12/case.
Sarnavap Self Adhered Primer
Sarnavap Self-Adhered Primer is a solvent-based primer used to prime wood, concrete, lightweight concrete, gypsum boards and decks, and DensDeck® boards prior to the application of Sarnavap Self-Adhered vapor barrier or Sarnafil G476 SA (Self-Adhered) waterproofing membrane.
Sarnavap Self Adhered Primer WB
Sarnavap Self-Adhered Primer WB is a water-based primer used to prime wood, concrete, lightweight concrete, gypsum boards and decks, and DensDeck® boards prior to the application of Sarnavap Self-Adhered vapor barrier or Sarnafil G476 SA (Self-Adhered) waterproofing membrane.
Surface Conditioner 150
Surface Conditioner 150 is a specially formulated water-based surface treatment that will bind residual site dust and concrete efflorescence prior to the installation of Sarnafil G476 SA (Self-Adhered) waterproofing membrane. The surface conditioner promotes the adhesion of the self-adhered membrane to properly prepared and conditioned concrete and masonary substrates.
Sarnasolv is used for the general cleaning of residual asphalt, scuff marks, etc. from Sarnafil membrane surfaces. Sarnasolv is also used daily to clean seam areas prior to hot-air welding in tear-off or dirty conditions or if the membrane is not welded soon after it is unrolled.